Hi I am seeking your advice on the setup of: Lintrack As A LAN Gateway And An OpenVPN Bridge which posted at http://www.howtoforge.com/lintrack_lan_gateway_openvpn_bridge. I have failed to setup as per the procedures given. I have setup two x86 PC hosts, with at 512MB of RAM and 9GB of storage space, two ethernet cards and did not install WiFi card. I installed only the Lintrack-mini-2.0 on both hosts.Hosts rt1 and rt2 are our routers running Lintrack. Both of them have Internet connection, (rt1 via SDSL and rt2 via SDSL modems), a public IP address available on eth0 interface and a Local Area Network behind as follow: Host Via Addr Type IP Address Gateway IP rt1 SDSL modem Public 203..xxx.xxx.171/28 203.xxx.xxx.161 rt2 ADSL modem NAT 192.168.yyy.yyy/24 192.168.yyy.1 Host Local Address rt1 192.168.1.1 rt2 192.168.1.2 NB: Not wireless was setup. I have formatted the drive on both system and installed as fresh. Below shown the rt1 configuration: fcc cd sys set hostname rt1.lan set hostip 192.168.1.1 Configure eth0 interface: cd / net if eth add +if eth0 cd eth0 set descr "Internet uplink" add ip +addr main set ip main addr 230.xxx.xxx.171/28 The LAN bridge: cd .. add +if eth1 cd .. br add +if br0 cd br0 set descr "LAN bridge" add +if eth1 add ip +addr main set ip main addr 192.168.1.1/24 Default route and DNS server: cd / net set route quickgw 203.xxx.xxx.161 add dns +servers 192.169.34.181 The firewall with two zones - "internet": cd fw add +zone internet cd internet add +matches uplink set uplink if eth0 set srv forwarding to set actions masq true ...and "lan": cd .. add +zone lan cd lan add +matches bridge set bridge if br0 cd srv set forwarding on igmp true dhcp true dns true cd .. actions set clampmss true Finally - we enable dnsmasq as DNS cache and DHCP server: cd / srv dnsmasq set boot true set dhcp true auth true from 192.168.1.50 to 192.168.1.150 Below shown the rt2 configuration: fcc cd sys set hostname rt1.lan set hostip 192.168.1.1 Configure eth0 interface: cd / net if eth add +if eth0 cd eth0 set descr "Internet uplink" add ip +addr main set ip main addr 230.xxx.xxx.171/28 The LAN bridge: cd .. add +if eth1 cd .. br add +if br0 cd br0 set descr "LAN bridge" add +if eth1 add ip +addr main set ip main addr 192.168.1.1/24 Default route and DNS server: cd / net set route quickgw 192.168.yyy.1 add dns +servers 203.120.90.40 The firewall with two zones - "internet": cd fw add +zone internet cd internet add +matches uplink set uplink if eth0 set srv forwarding to set actions masq true ...and "lan": cd .. add +zone lan cd lan add +matches bridge set bridge if br0 cd srv set forwarding on igmp true dhcp true dns true cd .. actions set clampmss true Finally - we enable dnsmasq as DNS cache and DHCP server: cd / srv dnsmasq set boot true set dhcp true auth true from 192.168.1.151 to 192.168.1.250 I have manually enable basic networking as per your procedures: cd /etc/rc.d ./rc.firewall restart ./rc.eth eth0 start ./rc.eth eth1 start ./rc.br br0 start ./rcS.d/S40staticrt As mentioned: This should give you access to both machines from Internet and wired LAN. I failed to accesss to both machines from the internet and wired LAN. Pls advice. Thank You Eddiequekl