I know I've probably done something incorrectly, but I can't get past page 4 of the setup... [X] Downloading the latest release notes... Test result: Failure For some reason, the machine will not connect to the site to download the release notes & updates. Here's what's in the logs: Code: [B] Kernel Network Interfaces[/B] eth0 Link encap:Ethernet HWaddr 00:16:17:A1:4F:29 inet addr:192.168.1.110 Bcast:192.168.7.25 Mask 255.255.248.0 inet6 addr: fe80::216:17ff:fea1:4f29/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 METRIC:1 Rx packets:145 errors:0 dropped:0 overruns:0 frame:0 Tx packets:161 errors:0 dropped:0 overruns:0 carrier:0 collision:0 txqueuelen:1000 RX bytes: 31569 (30.8Kb) Tx bytes:11722 (11.4Kb) Interrupt:217 base address:0Xf200 lo Link encap local loopback inetaddr:127.0.0.1 Mask:255.0.0.0 inetaddr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU: 16436 METRIC:1 Rx packets:212 errors:0 dropped:0 overruns:0 frame:0 Tx packets:212 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txueuelen:0 [B] Kernel Routing Table[/B] Kernel IP Routing Table Destination Gateway Genmask Flag Metric Ref 192.168.0.0 0.0.0.0 255.255.248.0 U 0 0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 [B]Hostname Lookup[/B] domain domain.co <and no, there is no 'm' on the end> [B]Download of release notes(openSuse 10.2)[/B] *getaddrinfo(3) failed for www.suse.com:80 *couldn't resolve host 'www.suse.com' *closing connection #0 curl: (6) couldn't resolve host 'www.su [B]Kernel Messages[/B] logger: BEGIN OF YAST2 INTERNET TEST ifstatus: eth0 device: VIA TECHNOLOGIES, INC VT6102 [Rhine II] (rev 7c) ifstatus: eth0 configuration: eth-id-00:16:17:a1:4f:29 ifstatus: eth0 is up ifstatus2: eth0 <BROADCAST,MULTICAST,UP,10000> mtu1500 qdisc pfifo-fast qlen 1000 ifstatus: link/ether 00:16:17:a1:4f:29 brd ff :ff:ff:ff:ff:ff ifstatus: inet 192.168.1.110/21 brd 192.168.7.255 scope global eth0 ifstatus: inet6 fe80::216:17ff:fea1:4f29/64 scope link valid_lft forever preferred_lft forever ifstatus: eth0 ip address:192.168.1.110/21 ifstatus-route: Configured routes for interface eth0 ifstatus-route: default 192.168.1.1 - - ifstatus-route: 169.254.0.0 - 255.255.0.0 eth0 ifstatus-route: Active routes for interface eth0 ifstatus-route: 192.168.0.0/21 proftp kernel scope link src 192.168.1.110 ifstatus-route: 169.254.0.0/16 scope link I'm using a Linksys Wireless G Router WRT54G IP Address 75.XXX.XXX.XXX Subnet Mask 255.255.248.0 Default Gateway 75.XXX.XXX.X DNS1 208.XXX.XX.XX DNS2 208.XXX.XX.XXX MTU 1500 Anyone have any idea?
I continued the install letting the program set the ip address and was able to continue the setup and download the updates. Should I continue with the setup and then go back and try to adjust the appropriate settings to my network?
Automatice DHCP My router has a setting to act as a DHCP server. I'm going to try and turn that off and see if it will allow me to assign an ip address.
I'm using DHCP as well, but still I can assign a static IP address to my SuSE system, as shown here: http://www.howtoforge.com/perfect_setup_opensuse_10.2_p3