I set up vmware on dapper drake ubuntu with NAT (see ifonfig below(A) then suddenly yeaterday no more NAT (see what ifconfig looks like below(B) why has NAT setting suddely dissaperared? Happy New Year falko (A) eth0 Link encap:Ethernet HWaddr 00:0F:B0:5C:AF:1F inet addr:192.168.1.64 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::20f:b0ff:fe5c:af1f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:370706 errors:0 dropped:0 overruns:0 frame:0 TX packets:369586 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:177062373 (168.8 MiB) TX bytes:146384318 (139.6 MiB) Interrupt:201 Base address:0xcc00 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:719 errors:0 dropped:0 overruns:0 frame:0 TX packets:719 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:164176 (160.3 KiB) TX bytes:164176 (160.3 KiB) sit0 Link encap:IPv6-in-IPv4 NOARP MTU:1480 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) vmnet1 Link encap:Ethernet HWaddr 00:50:56:C0:00:01 inet addr:172.16.163.1 Bcast:172.16.163.255 Mask:255.255.255.0 inet6 addr: fe80::250:56ff:fec0:1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) vmnet8 Link encap:Ethernet HWaddr 00:50:56:C0:00:08 inet addr:172.16.0.1 Bcast:172.16.0.255 Mask:255.255.255.0 inet6 addr: fe80::250:56ff:fec0:8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:940 errors:0 dropped:0 overruns:0 frame:0 TX packets:78 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) collisions:0 txqueuelen:1000 ------------------------------------------------------------------------------------ (B) eth0 Link encap:Ethernet HWaddr 00:0F:B0:5C:AF:1F inet addr:192.168.1.64 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::20f:b0ff:fe5c:af1f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:642580 errors:0 dropped:0 overruns:0 frame:0 TX packets:456962 errors:0 dropped:0 overruns:1 carrier:0 collisions:0 txqueuelen:1000 RX bytes:795955806 (759.0 MiB) TX bytes:87752831 (83.6 MiB) Interrupt:201 Base address:0x6c00 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:244 errors:0 dropped:0 overruns:0 frame:0 TX packets:244 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:75318 (73.5 KiB) TX bytes:75318 (73.5 KiB)
Nat Thankyou falko re-boot was the answer. I wonder if you might point me to a howto to encrypt a external usb hard drive? I CANNOT boot into the external hard drive because of my BIOS on my labtop does not have this facility, I can only save data on to the hard drive. radox
Take a look here: http://www.sdc.org/~leila/usb-dongle/readme.html http://www.hermann-uwe.de/blog/howto-encrypted-usb-thumb-drives-and-usb-hard-disks-using-loop-aes