Hello again, Well I'm back, I have lost my connection to the web once more. I have on my dual boot machine Win XP and Fedora Core 5, I was up and running on XP, then rebooted and booted up Fedora, only to find that i couldn't get on line? I have been running online in Fedora for about 6 days without a hitch. My Network say's I'm activated,But I can't get on line, My firefox is running, yet it can't find the servers? I tried to restart with the /etc/init.d/network restart command and all commands I know, Maybe someone else that had this problem can help? Thanks. fvs
Does your Fedora system use DHCP or a static IP address? What's in /etc/sysconfig/network-scripts/ifcfg-eth0?
Hi Falko, I can't seem to get it together, [root@localhost frank]# /sbin/route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 169.254.0.0 * 255.255.0.0 U 0 0 0 lo [root@localhost frank]# /etc/init.d/network restart Shutting down interface eth0: [ OK ] Shutting down loopback interface: [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface eth0: Determining IP information for eth0...dhclient(3319) is already running - exiting. exiting. failed [root@localhost frank]# dmesg | grep eth0 eth0: forcedeth.c: subsystem: 01565:2501 bound to 0000:00:14.0 eth0: no IPv6 routers present eth0: no IPv6 routers present eth0: no IPv6 routers present [root@localhost frank]# # nVidia Corporation MCP51 Ethernet Controller DEVICE=eth0 BOOTPROTO=dhcp HWADDR=00:E0:4C:F1:A3:FE ONBOOT=yes USERCTL=no IPV6INIT=no PEERDNS=yes TYPE=Ethernet IPADDR=192.168.0.3 DEFAULTGATEWAY=192.168.0.1 NETMASK=255.255.255.0 GATEWAY=192.168.0.1 ~ ~ ~ ~ ~
Can you try this in /etc/sysconfig/network-scripts/ifcfg-eth0? Code: DEVICE=eth0 BOOTPROTO=static BROADCAST=192.168.0.255 HWADDR=00:E0:4C:F1:A3:FE IPADDR=192.168.0.3 NETMASK=255.255.255.0 NETWORK=192.168.0.0 ONBOOT=yes GATEWAY=192.168.0.1 DEFAULTGATEWAY=192.168.0.1 Restart the network afterwards: Code: /etc/init.d/network restart Your system should then have the IP address 192.168.0.3.
OK, I have it all except I still can't get to the internet? Check it out: ssword: [root@localhost frank]# /etc/init.d/network restart Shutting down interface eth0: [ OK ] Shutting down loopback interface: [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface eth0: [ OK ] [root@localhost frank]# ping 192.168.0.3 PING 192.168.0.3 (192.168.0.3) 56(84) bytes of data. 64 bytes from 192.168.0.3: icmp_seq=1 ttl=64 time=0.051 ms 64 bytes from 192.168.0.3: icmp_seq=2 ttl=64 time=0.049 ms 64 bytes from 192.168.0.3: icmp_seq=3 ttl=64 time=0.045 ms 64 bytes from 192.168.0.3: icmp_seq=4 ttl=64 time=0.043 ms 64 bytes from 192.168.0.3: icmp_seq=5 ttl=64 time=0.043 ms 64 bytes from 192.168.0.3: icmp_seq=6 ttl=64 time=0.046 ms 64 bytes from 192.168.0.3: icmp_seq=7 ttl=64 time=0.045 ms 64 bytes from 192.168.0.3: icmp_seq=8 ttl=64 time=0.051 ms 64 bytes from 192.168.0.3: icmp_seq=9 ttl=64 time=0.045 ms 64 bytes from 192.168.0.3: icmp_seq=10 ttl=64 time=0.044 ms 64 bytes from 192.168.0.3: icmp_seq=11 ttl=64 time=0.048 ms 64 bytes from 192.168.0.3: icmp_seq=12 ttl=64 time=0.044 ms 64 bytes from 192.168.0.3: icmp_seq=13 ttl=64 time=0.045 ms 64 bytes from 192.168.0.3: icmp_seq=14 ttl=64 time=0.048 ms 64 bytes from 192.168.0.3: icmp_seq=15 ttl=64 time=0.044 ms 64 bytes from 192.168.0.3: icmp_seq=16 ttl=64 time=0.043 ms 64 bytes from 192.168.0.3: icmp_seq=17 ttl=64 time=0.047 ms 64 bytes from 192.168.0.3: icmp_seq=18 ttl=64 time=0.049 ms --- 192.168.0.3 ping statistics --- 18 packets transmitted, 18 received, 0% packet loss, time 16998ms rtt min/avg/max/mdev = 0.043/0.046/0.051/0.004 ms [root@localhost frank]# root@localhost frank]# /sbin/route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0 169.254.0.0 * 255.255.0.0 U 0 0 0 eth0 default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 [root@localhost frank]#
Is 192.168.0.1 your gateway? Can you ping other systems in your local network? Where does 169.254.0.0 come from?
What ethernet card do you use. Download its latest driver from the manufactures website and then extract them with cabextract (yum install cabextract). Install ndiswrapper http://www.linuxquestions.org/linux/?q=answers/Networking/Ndiswrapper_in_Fedora_Core_5& Then run cabextract on the .exe file. Install the required .ini or .inf (google this) and then type depmod -a and then ndiswrapper -m and you should be good.
Can't go to web site, I can't get online with Fedora 5, I'm writing you in Win XP system. Need to get online in linux fedora Core5.
Fvs, It looks like your eth0 is coming up fine, but that you may not be getting DNS information. For giggles, try to ping yahoo.com by using its IP address: ping 66.94.234.13 and see how that goes. If that works then it is a DNS issue. HTH, Jim
[root@localhost frank]# /sbin/ifconfig eth0 Link encap:Ethernet HWaddr 00:E0:4C:F1:A3:FE inet addr:192.168.0.250 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::2e0:4cff:fef1:a3fe/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:201 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:17 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:2220 errors:0 dropped:0 overruns:0 frame:0 TX packets:2220 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2677417 (2.5 MiB) TX bytes:2677417 (2.5 MiB) Tried to ping Yahoo.com & 66.94.234.13 , can't go through
I really hope this isn't as easy as I think it is. If you can ping an ip address (any address at all) your ethernet is working, and network connectivity is NOT your issue. Your DHCP appears to have assigned you an address (as show by ifconfig). If you try pinging by name (NOT ip) you will probably find it can't. The reason being it CANNOT resolve names. You need to specify a dns server in /etc/resolv.conf . Therefore firstly : cat /etc/resolv.conf to see what you got. Then pico/nano/vi your /etc/resolv.conf file and add in this at the top nameserver 82.138.242.202 I would only recommend using this entry for a short time as it's my DNS server, and your ISP should have one you can use instead. You could probably also use your routers/gateway IP (192.168.0.1 or whatever it is). UPDATE : Ok, i decided to re-read a couple of posts here. You cannot access an external network. So check the following : cat /etc/sysconfig/network Make sure you have a line like : GATEWAY=192.168.0.1 You must specify your gateway address else you'll never get an external connection. ________ Live sex
Thanks for reply, I have it working now with a lot of tweaking and luck, Don't ask me how, i just set it back to DHCP and it came back on reboot? Hope it lasts after next update. Thanks. fvs
I can't go any further,I'm stuck with out an internet connection. Once again I take one step forward and two steps back, This time all was going well with my internet and I thought that I would start going ahead and download the programs that would help personalize my system, I used update to update my system the and commenced to install samba, anjuta and a few other things, I guess in the update it included a new kernel 2.6.16 and when I rebooted once again and found Once more I hadn't a connection to the web and no server. Went through all the connands & code we did in the last two weeks the last one, etc/init.d/network restart and found error message that said something about errors and refered me to /etc/syscongig/network-scripts/ifup-eth, I don't know what I should look for? This FC5 is rather differcult to handle for a novice. I'm glad to have your help, Thanks fvs
Check /etc/sysconfig/network-scripts/ifcfg-eth0 it will contain your ethernet address information. ________ LilyH
